证：工商信息已核宝br /> 访问量：239199
SML Resist Product Information
Introduction
The hardware of electron beam lithography has improved continuously over the past few decades＋/span>but electron beam resist technology has not and this is now one of the main limiting factors inimproved EBL performance.
The high performance SML resist is a novel polymer that has been specifically designed to answerthe demands of the EBL community. It can be simultaneously patterned into high resolution andhigh aspect ratio patterns even at low acceleration voltages and without the aid of proximity effectcorrection.
Processing
Other Processing Information
Slow dry etch rate: significantly slowerthan PMMA
Can be hard-baked: Tg=109ℂ/span>
Can be re-exposed after development
Other developers such as IPA:H2O canalso be used
Shelf life is guaranteed for 6 months
Products Spin Curves
How it Works - Monte Carlo Simulations
The following Monte Carlo simulations compare the electron scattering behaviour of PMMA andSML resists at 30KeV and at 100KeV. Each simulation contains 500 incident electrons and createdsecondary electrons are shown in light blue.
Comparison of 50nm thick PMMA & SML on Si substrate exposed @30keV
These simulations show that at both 30KeV and 100KeV:
The lateral scattering of incident electrons is much less in SML than in PMMA
。The number of secondary electrons created is much less in SML than in PMMA
These properties mean that SML resist is less susceptible to the problem of proximity effect andenables the patterning of features with smaller critical dimensions larger aspect ratio andstraighter side-walls than those obtainable in PMMA resist.
About EM Resist Ltd
EM Resist Ltd specialises in electron beam lithography resists and applications. We develop andmanufacture electron beam resists in a purpose built cleanroom facility to ensure maximumquality and performance. We also have a dedicated team of applications scientists to aid ourcustomers with their questions and requirements.
Our products and expertise are the result of many years research by experienced physicists andmaterial scientists in both academia and industry. We are based in Macclesfield UK and haveglobal sales and distribution channels for our products.
SML Resist Processing Information
Introduction
SML resist has been specifically designed for electron beam lithography. It is a polymer materialand can be processed in exactly the same way as other polymer resists such as PMMA or ZEP.
Storage
Do not refrigerate.
Store at room temperature.
Store away from direct sunlight and ignition sources.
The shelf life is guaranteed for six months.
Typical Processing Conditions
The processes outlined below are our standard processes. Other common resist processes canalso be used.
Substrate Preparation:
Solvent clean with Acetone and IPA.
SML has excellent adhesion to most substrates so HMDS is not generally required.
Spin Coating:
See spin curves below.
Baking:
Hot plate @ 180 C for 120-180 seconds.
Exposure:
Development:
MIBK:IPA (1:3) for 30 seconds followed by a rinse in IPA for 15 seconds.
Hard-Bake:
Convection oven @ 80 C for 30 minutes. (Tg=109ℂspan> )
Remover:
Acetone.
Spin Curves
Spin coater settings:
。Ramp up time = 5 seconds.
。Spin time = 20 seconds.
。Ramp down time = 10 seconds.
Safe Handling and Disposal
Caution: Flammable liquid.
Open in a well ventilated area.
Avoid inhalation.
Avoid direct contact with skin and eyes.
Wear appropriate safety equipment such as glasses and gloves.
In case of direct contact with eyes rinse thoroughly with water and seek medical advice.
Read the Material Safety Data Sheet.
Dispose of in appropriate waste containers for non-halogenated waste.
About EM Resist Ltd
EM Resist Ltd specialises in electron beam lithography resists and applications. We develop andmanufacture electron beam resists in a purpose built cleanroom facility to ensure maximum
quality and performance. We also have a dedicated team of applications scientists to aid our
customers with their questions and requirements.
Our products and expertise are the result of many years research by experienced physicists and
material scientists in both academia and industry. We are based in Macclesfield UK and have
global sales and distribution channels for our products.
100 KeV Exposure Parameters
Please note that the best results (aspect ratio and resolution) are generallyachieved when a relatively low beam current is used.
100 KeV Exposure Parameters
30 KeV Exposure Parameters
25 KeV Exposure Parameters
SML Resist Contrast & Sensitivity
SML A Complete Solution for you Part 1 / 2
E M Resist can offer two complete solutions to suit your distribution needs in your territory.
SML A Complete Solution for you Part 2 / 2
- 推荐产品
- 供应产品
- 产品分类
- 芬兰PICOSUN标准型原子层沉积机R-200
- PICOSUN P-200S Pro ALD生产型原子层沉积朹/a>
- 芬兰PICOSUN标准型原子层沉积机R-200
- 德国Moeller光学?静态接触角?界面测量仪SL150
- 日本JEOL能谱仪JED-2300T
- 日本JEOL粉末装置TP-99010FDR
- 德国Sentech台式薄膜探针反射仪FTPadv
- 日本JEOL能谱仪，JED-2300，JED-2300F
- 德国Sentech集成多腔等离子刻蚀和沉积机
- 日本JEOL热场发射扫描电子显微镜JSM-7200F
- N-TEC全自动LED晶圆贴标解胶机BW 227-7FA
- N-TEC全自动片机晶圆贴BW 243FA
- 日本JEOL扫描电子显微镜JSM-IT500HR
- 日本JEOL电子自旋共振谱仪JES-X3
- 德国laVision BioTec光片照明显微镜Ultramicroscop
- 半导体测试探针台KUP007，EMP100C，EMP100B，EMP50S